Problems Receiving Faxes
10-Dec-2010
8201023600
Issue
Cause and Solution
[ Cannot Receive a Fax, Cannot Print a Fax ]
[ Machine Does Not Switch Automatically between Voice and Fax Calls ]
[ Quality of Received Fax is Poor ]
[ Cannot Receive a Color Fax ]
[ Errors Often Occur When You Receive a Fax ]
- You cannot receive faxes if the power is turned off. Press the ON button to turn the power on.
- If you disconnected the power cord without turning off the power (one of the buttons on the Operation Panel is lit), reconnecting it turns on the power automatically.
- If you disconnected the power cord after pressing the ON button to turn off the power (no buttons on the Operation Panel are lit), reconnect it, then press the ON button to turn on the power.
- If the power was turned off due to power failure, etc., the power is automatically turned on when the power failure is resolved.
A: ON button
B: FAX Memory lamp
IMPORTANT
- Confirm that all lamps on the Operation Panel are off before unplugging the power cord, then unplug the power cord. If a power failure occurs or you unplug the power cord, all faxes stored in the machine's memory are deleted.
REFERENCE
If the faxes stored in machine's memory are deleted by a power failure or unplugging the power cord, the list of the faxes deleted from the machine's memory will be printed after turning the machine on.
Print the received faxes stored in machine's memory or save them on the memory card/USB flash drive, delete them from the machine's memory, and have the sender resend the faxes.
Document Stored in Machine's Memory
If the sending faxes is not complete or the machine was not able to print the received faxes, these faxes are stored in machine's memory.
If an error occurred during a fax transmission, the document is not stored in machine's memory.
In the following cases, the machine is not able to print the received fax and will automatically store the fax in its memory.
- Check the LCD for an error message.
- Print the Activity report and check for an error.
Check that the telephone line is connected correctly to the Telephone Line Jack and that the telephone (or another external device such as an answering machine or a computer modem) is connected correctly to the External Device Jack. Refer to your setup manual.
Initial Hardware Setup
Preparation
Confirming the Telephone Line Connection
For the basic connection of the machine, refer to [ Initial Hardware Setup ] .
The machine cannot send/receive faxes if the connection is incorrect. Connect the machine correctly.
If a different size of paper from that specified by [ Page size ] is loaded for printing faxes, the received faxes will not be printed and will be stored in machine's memory (Memory Reception). Load the same size of paper as that specified by [ Page size ], then press the OK button on the machine.
If [ Page size ] is set to other than [ A4 ], [ Letter ], or [ Legal ], the received fax will not be printed and will be stored in machine's memory (Memory Reception). Set [ Page size ] to [ A4 ], [ Letter ], or [ Legal ].
If [ Type ] is set to other than [ Plain paper ], the received fax will not be printed and will be stored in machine's memory (Memory Reception). Set [ Type ] to [ Plain paper ].
If paper is not loaded, received faxes will be stored in machine's memory without being printed. Load paper, then press the OK button.
Loading Paper
Loading Plain Paper / Photo Paper
See[Loading Paper]
If the amount of remaining ink is insufficient to print, received faxes will be stored in machine's memory without being printed. Check the ink level and take the appropriate action, then print the faxes in machine's memory.
REFERENCE
- If the machine was receiving faxes in the fax mode, printing will start automatically after checking the ink level and taking appropriate action.
-> [ Replace ink cartridge(s) ]
- You can set the machine to forcibly print a received fax even if the ink has run out. However, part or all of the fax may not be printed since the ink has run out. Also, the contents of the fax will not be stored in machine's memory. If the ink has already run out, we recommend that [ Do not print ] be selected for [ Received documents ] in [ Auto print settings ] under [ FAX settings ] to store the received fax in machine's memory. After you check the ink level, take the appropriate action, and select [ Print ] for [ Received documents ] in [ Auto print settings ], the fax stored in machine's memory will be printed automatically.
Check the receive mode setting and change it to a mode suited to your connection if necessary.
Receiving Faxes
This section describes the preparation necessary for receiving a fax and how to receive a fax. This section also describes the operation to print documents stored in the machine's memory such as when ink or paper runs out.
(A) Prints a received fax......
See[Receiving Faxes ]
Select [ OFF ] for [ FAX reception reject in Security control ] under [ FAX settings ].
If you select Reject for any setting items in [ Caller rejection in Security ] control under [ FAX settings ], the machine rejects calls for setting item selected [ Reject ].
If [ FAX only mode ] is selected for [ Receive mode settings ], there will be no automatic switching between voice and fax calls.
Set the receive mode to [ TEL priority mode, DRPD ]*1, or [ Network switch ]*2.
If the receive mode is [ TEL priority mode ] and an answering machine is connected to the machine, check whether a proper message is played back when the answering machine answers.
*1 This setting is available only in the US and Canada.
*2 This setting may not be available depending on the country or region of purchase.
Receiving Faxes
This section describes the preparation necessary for receiving a fax and how to receive a fax. This section also describes the operation to print documents stored in the machine's memory such as when ink or paper runs out.
(A) Prints a received fax......
See[Receiving Faxes ]
Ask the sender to adjust the scan settings of the fax machine.
Select [ ON ] for [ ECM RX ] in [ Adv. communication settings ] in [ Advanced FAX settings ] under [ FAX settings ].
If [ ECM RX ] is enabled, the sender's fax machine resends the fax after correcting errors automatically.
The image quality of the fax is mainly determined by the sender's fax machine. Contact the sender and ask the sender to check whether the scanning area of the fax machine is dirty.
Check 4: Is ECM transmission/reception enabled although the line/connection is poor, or is the sender's fax machine compatible with ECM?
- Select [ ON ] for [ ECM RX ] in [ Adv. communication settings ] in [ Advanced FAX settings ] under [ FAX settings ].
- Contact the sender and ask the sender to check whether the machine is set to enable ECM transmission. If the sender's or recipient's fax machine is not compatible with ECM, the fax will be sent/received without automatic error correction.
- Reduce the reception start speed on [ RX start speed ] in [ Adv. communication settings ] in [ Advanced FAX settings ] under [ FAX settings ].
If [ OFF ] is select for [ ECM RX ] in [ Adv. communication settings ] in [ Advanced FAX settings ] under [ FAX settings ], the machine cannot receive color faxes. The machine will disconnect the telephone line or receive color faxes in black & white according to the setting of the sender's fax machine.
Set [ ECM RX ] to [ ON ].
If the telephone line or connection is poor, reducing the reception start speed may correct the error.
Reduce the reception start speed on [ RX start speed ] in [ Adv. communication settings ] in [ Advanced FAX settings under FAX settings ].
Contact the sender and ask the sender to check whether the fax machine is operating normally.