01-Feb-2013
0400015406
Saya telah membaca dan memahami disclaimer di bawah, dan ingin mengunduh perangkat lunak yang ditunjuk.
You can use this program to update the printer firmware version.
Modifications from Ver.1.40 to Ver.1.41
1. Fix the hung up issue rarely occurs when going into sleep mode.
2. Fix the paper jam with plain paper which rarely happens at the leading edge of roll paper.
3. The problem that the community name setting in SNMP setting was not processed correctly has been fixed.
4. Shutdown timer function has been added.
-Shutdown timer
After the printer goes into Sleep Mode, power will be turned off automatically when the situation that the printer is not operated continues until the time being set in advance by operation panel.
Setup time:OFF/ 5 min./ 10 min./ 30 min./ 1 hour/ 4 hours/ 8 hours*/ 12 hours *Initial value when updating version.
Note:
To fix the issue 2., please apply the MCT versions below to the printer and its driver after upgrading the firmware.
Windows 32bit 2.7205
Windows 64bit 2.7205
Mac OS X v10.4-v10.7 2.75
Mac OS X v10.2-v10.3 2.7405
Modifications from Ver.1.36 to Ver.1.40
1. The acquisition of serial number of main body by iWEMC supported
2. The failure of retrieving from sleep mode on rare occasions fixed
3. The failure of inability to print in HP/GL2 printing when file name contains 2-byte character(s) and the second byte is "5C" (back slash) fixed
4. The drive control in printing optimized
Modifications from Ver.1.35 to Ver.1.36
1. In case the nozzles are clogged, formerly you would stop printing and check the printout,
and then continue printing by pressing the Online key.
Now it automatically checks the level of clogging, and if it is possible to print it will continue printing,
and if it needs a printhead replacement, it will display a Replace Printhead message.
This modification will greatly improve the workability.
2. Functions in the HP-GL/2 mode have been improved (speed up).
Use this program with the systems and the operating environments below.
Software: Microsoft Windows 8 64-bit edition, English Edition
Microsoft Windows Server 2012 64-bit edition, English Edition
Microsoft Windows 7 64-bit edition, English Edition
Microsoft Windows Server 2008 R2 64-bit edition, English Edition
Microsoft Windows Server 2008 64-bit edition, English Edition
Microsoft Windows Vista 64-bit edition, English Edition
Microsoft Windows Server 2003 R2 64-bit edition, English Edition
Microsoft Windows Server 2003 64-bit edition, English Edition
Microsoft Windows XP Professional 64-bit edition, English Edition
Hardware: Any computer running the software listed above.
Interface Connectivity:
The printer and computer where this program is executed must be connected
with either of the following methods.
- Connected via a TCP/IP network and capable of printing via the network.
- Connected via a USB or IEEE 1394 port cable and capable of printing
as a local printer.
Note: If you are using IEEE1394, IEEE1394 Class Driver is needed.
The following limitations apply to the use of this program.
Before using the program, make sure that you understand these limitations.
* You must log into Windows as an Administrator before the installation.
* Before you start the firmware version update program, close any other applications
that are running.
* Do not try to use the printer while the firmware version update program is running.
If a print job is executing, cancel the print job or wait for the job to finish
before you execute the version update program.
* Never switch off the target printer while the firmware version update program is running.
* If the firmware version update fails while writing to the flash ROM,
you may not be able to start the printer. In this case,
contact a Canon service center or the dealer where you purchased the printer.
(1) Switch the printer on.
(2) When you have downloaded the file, decompress it on your computer hard disk.
(3) Execute the setup file. The imagePROGRAF Firmware Update Tool is installed.
(4) From the Start menu, select Programs to execute imagePROGRAF Firmware Update Tool.
Semua perangkat lunak, program (termasuk namun tidak terbatas pada driver), file, dokumen, manual, instruksi, atau materi lainnya (secara bersama-sama disebut "Konten") tersedia di situs ini atas dasar "sebagaimana adanya".
Canon Singapore Pte. Ltd., dan perusahaan afiliasinya (“Canon”) tidak memberikan jaminan dalam bentuk apa pun sehubungan dengan Konten, secara tegas menyangkal semua jaminan, tersurat maupun tersirat (termasuk, tanpa batasan, jaminan tersirat tentang dapat diperjualbelikan, kesesuaian untuk tujuan tertentu dan non-pelanggaran) dan tidak bertanggung jawab untuk memperbarui, mengoreksi, atau memberikan dukungan Konten.
Canon memiliki semua hak milik, kepemilikan, dan hak kekayaan intelektual yang relevan dalam Konten. Anda dapat mengunduh dan menggunakan Konten hanya untuk penggunaan pribadi, non-komersial, dan dengan risiko Anda sendiri. Canon tidak bertanggung jawab atas kerusakan apa pun sehubungan dengan Konten, (termasuk, tidak terbatas untuk kerusakan tidak langsung, sebagian, ganti rugi atau kerusakan tidak disengaja).
Anda tidak boleh mendistribusikan, menetapkan, melisensikan, menjual, menyewakan, menyiarkan, mentransmisikan, menerbitkan, atau mentransfer Konten ke pihak lain mana pun. Anda juga tidak boleh (dan tidak akan membiarkan orang lain) mereproduksi, memodifikasi, memformat ulang, membongkar, mendekompilasi, atau merekayasa balik atau membuat karya turunan dari Konten, secara keseluruhan atau sebagian.
Anda setuju untuk tidak mengirim atau membawa Konten keluar dari negara/wilayah tempat Anda awalnya memperolehnya ke negara/wilayah lain tanpa izin yang diperlukan dari pemerintah yang berlaku dan/atau melanggar undang-undang, batasan, dan peraturan yang berlaku.
Dengan melanjutkan mengunduh Konten, Anda setuju untuk terikat oleh hal di atas serta semua hukum dan peraturan yang berlaku untuk pengunduhan dan penggunaan Konten oleh Anda.