24-Mar-2020
0400104302
Saya telah membaca dan memahami disclaimer di bawah, dan ingin mengunduh perangkat lunak yang ditunjuk.
Printer firmware for iPF650/iPF655.
Modifications from Ver.1.41 to Ver.1.50
1. Security enhancement (SHA-2) in connecting remote services.
2. Support for TLS v1.1 and TLSv1.2.
Modifications from Ver. 1.40 to Ver.1.41
1. The failure that occurs in rare case in firmware updating was modified.
2. The paper jam error that occurs in rare case in adjusting print head position with using cut papers was modified.
Modifications from Ver. 1.38 to Ver.1.40
1. modification of the failure that the data is printed dividing into two pages, or that the data is printed insufficiently when printing a particular HP-GL2 file.
2. modification of the failure that hanging up occurs after printing a particular HP-GL2 file.
Modifications from Ver. 1.36 to Ver.1.38
1. Following improvement was implemented for HP-GL/2 print function.
- Priority of HP-GL/2 process task was optimized to improve the network response delay.
- Printing failure due to HP-GL/2 data dividing was modified.
- Printing failure due to HP-GL/2 data combining was modified.
- The failure occurs at printing HP-GL/2 that includes large amount of linear data was modified.
- "Memory overflow" warning display error during long time intermittent printing was modified.
- The failure which fails to finish the job when sending data without end indicator in HP-GL/2 was modified.
- Printing failure which occurs to have non-printed band area over print head width when printing in particular HP-RTL data was modified.
- Solid black printing when communication is disconnected during HP-RTL data printing was modified.
- The handling method of transparent layer in JP-GL/2 data has been improved.
2. The failure which restarts right after power is on when accessing printers through RemoteUI or IPP (Internet Printing Protocol) was modified.
3. Panel display error was modified.
4. The failure which stops access mediation function when using accounting function in status monitor was modified.
Modifications from Ver.1.34 to Ver.1.36
1. The specific period of time for auto cleaning execution has been modified.
There could be a case that cleaning failure occurs on the color side when printing only with monochrome. To address this issue, the period of time for auto cleaning execution on the color side has been modified as follows.
Before: Auto cleaning is executed within the specific period of time depending on the usage environment (temperature/humidity).
After: Auto cleaning is executed on a regular basis.
Modifications from Ver.1.30 to Ver.1.34
1. Enhancement and improvement of HP-GL/2 function have been implemented. (iPF655)
Following setting items have been added to the HP-GL/2 menu on the control panel.
- [Over Size]: Function to print with setting margins
- [Print Centered]: Function to print in the center of media
- [Enlarge/Reduce]: Function to configure the scale factor (25%-400%)
- [Line width correction]: Function to set correction value of line width
(Target line width can be configured with [Pen Setup])
- [Detect image size]: Function to analyze image data and detect image size
Along with the addition of the setting items above, the function of
[Page Size Process 1] and [Page Size Process 2] have been deleted.
2. Fixed the failure that white line appears on the image under a certain condition.
Modifications from Ver.1.22 to Ver.1.30
1.Fix the hung up issue rarely occurs when going into sleep mode.
2.Optimized the control of the print head.
3.The problem that the community name setting in SNMP setting was not processed correctly has been fixed.
4. Shutdown timer function has been added.
-Shutdown timer
After the printer goes into Sleep Mode, power will be turned off automatically when the situation that the printer is not operated continues until the time being set in advance by operation panel.
Setup time:OFF/ 5 min./ 10 min./ 30 min./ 1 hour/ 4 hours/ 8 hours*/ 12 hours *Initial value when updating version.
Modifications from Ver.1.20 to Ver.1.22
1. Modifications due to parts change
2. The fairly infrequent failure of printer not retrieving from sleep mode has been fixed.
3. A failure in Remote UI has been fixed.
Modifications from Ver.1.15 to Ver.1.20
1. Improved functions in HP-GL/2
2. A menu that enables Scan Wait Time to be specified only for the leading edge has been added in operation panel.
3. The fairly infrequent problem of printer not being able to retrieve from sleep mode has been fixed.
Modifications from Ver.1.11 to Ver.1.15
The failure described below has been fixed.
- In rare cases, the error massage (adjustment failed) appears or abnormal images (shifted line or color) occur at the printer installation or execution of advanced head adjustment.
*Precautions for version upgrading
After version upgrade, perform one of the followings.
- For roll paper users:
Remove the paper once, and then reload it.
From [Setting/Adj. Menu] of printer, execute [Auto (Advanced)] in [Head Posi.Adj.].
- For cut sheet users:
Perform printing Status Print or the like.
After that, turn the power off and back on, and reload the paper.
From [Setting/Adj. Menu] of printer, execute [Auto (Advanced)] in [Head Posi.Adj.].
Modifications from Ver.1.09 to Ver.1.11
1. Addition of an A4-conversion cumulative no. of sheets counter display to the top area of the operation panel.
2. As a remedy for the cut linearity problem in clear films, the precut length has been changed from 50mm to 150mm.
Modifications from Ver.1.07 to Ver.1.09
1. Degrading of print quality in vertical texts which occurs when performing HP/GL printing has been fixed.
2. The failure that printing is disabled when performing HP/GL2 printing if file name contains double-byte character AND its 2nd byte is "5C"(backslash) has been fixed.
3. The failure that if the printer is left for more than one hour while replacing the head with "Open the upper cover" message displayed, an error occurs has been fixed.
Modifications from Ver.1.06 to Ver.1.07
1. Reduced operation noise with Plain Papers/Coated Papers when printing
2. The problem that when roll paper ended during printing, printing restarts from the next page after roll paper is refeeded has been fixed.
3. The problem that when paper size is changed (small -> large), back of paper is smeared in rare cases has been fixed.
4. The problem that when used with continuous power-on, it might mis-detect the roll paper end in rare cases has been fixed.
Modifications from Ver.1.01 to Ver.1.06
1. The problem in which a printing failure may occur in some CAD applications depending on the setting has been fixed.
2. The problem during network printing in which printing is disabled in rare occasions has been fixed.
Install the Firmware Update Tool if it is not installed.
Semua perangkat lunak, program (termasuk namun tidak terbatas pada driver), file, dokumen, manual, instruksi, atau materi lainnya (secara bersama-sama disebut "Konten") tersedia di situs ini atas dasar "sebagaimana adanya".
Canon Singapore Pte. Ltd., dan perusahaan afiliasinya (“Canon”) tidak memberikan jaminan dalam bentuk apa pun sehubungan dengan Konten, secara tegas menyangkal semua jaminan, tersurat maupun tersirat (termasuk, tanpa batasan, jaminan tersirat tentang dapat diperjualbelikan, kesesuaian untuk tujuan tertentu dan non-pelanggaran) dan tidak bertanggung jawab untuk memperbarui, mengoreksi, atau memberikan dukungan Konten.
Canon memiliki semua hak milik, kepemilikan, dan hak kekayaan intelektual yang relevan dalam Konten. Anda dapat mengunduh dan menggunakan Konten hanya untuk penggunaan pribadi, non-komersial, dan dengan risiko Anda sendiri. Canon tidak bertanggung jawab atas kerusakan apa pun sehubungan dengan Konten, (termasuk, tidak terbatas untuk kerusakan tidak langsung, sebagian, ganti rugi atau kerusakan tidak disengaja).
Anda tidak boleh mendistribusikan, menetapkan, melisensikan, menjual, menyewakan, menyiarkan, mentransmisikan, menerbitkan, atau mentransfer Konten ke pihak lain mana pun. Anda juga tidak boleh (dan tidak akan membiarkan orang lain) mereproduksi, memodifikasi, memformat ulang, membongkar, mendekompilasi, atau merekayasa balik atau membuat karya turunan dari Konten, secara keseluruhan atau sebagian.
Anda setuju untuk tidak mengirim atau membawa Konten keluar dari negara/wilayah tempat Anda awalnya memperolehnya ke negara/wilayah lain tanpa izin yang diperlukan dari pemerintah yang berlaku dan/atau melanggar undang-undang, batasan, dan peraturan yang berlaku.
Dengan melanjutkan mengunduh Konten, Anda setuju untuk terikat oleh hal di atas serta semua hukum dan peraturan yang berlaku untuk pengunduhan dan penggunaan Konten oleh Anda.