Paper Is Smudged/Printed Surface Is Scratched
16-Jul-2008
8200216700
Issue
Cause and Solution
- Check to see if the paper you are printing on is suitable for your printing purpose.
->[ Media Types You Can Use ]
- When performing Borderless Printing, make sure that the paper you are using is suitable for Borderless Printing. If the paper you are using is not suitable for Borderless Printing, the print quality may be reduced at the top and bottom edges of the paper.
->[ Printing Area ]
- For Plain Paper
Turn the paper over and reload it to print on the other side.
Leaving the paper loaded on the Rear Tray for a long time may cause the paper to curl. In this case, load the paper with the other side facing up. It may resolve the problem.
We recommend putting unused paper back into the package and keeping it on a level surface.
- For Other Paper
1.With the printing side (A) facing up, cover the paper with a fresh sheet of plain paper to avoid staining or scratching the surface.
2.Roll up the paper in the opposite direction to the paper curl as seen below.
3.Check to see that the paper curl is within approximately 0.08 to 0.2 inches /2 to 5 mm (B) in height.
We recommend printing curl-corrected paper one sheet at a time.
NOTE
Depending on the media type, the paper may be smudged or may not be fed properly even if it is not curled. In such cases, follow the procedure described above to curl the paper before printing. This may improve the print result.
Selecting the Prevent paper abrasion setting will widen the clearance between the Print Head and the loaded paper. If you notice abrasion even with the media type set correctly to match the loaded paper, set the printer to prevent paper abrasion by using the printer driver.
Print speed is reduced if you are selecting the Prevent paper abrasion setting.
* Deactivate the Prevent paper abrasion setting once printing is complete. If not, this setting remains enabled for all subsequent print jobs.
Open the printer properties dialog box, and in Custom Settings in the Maintenance sheet, select the Prevent paper abrasion check box, and then click Send.
In the Canon IJ Printer Utility, select Custom Settings in the pop-up menu, select the Prevent paper abrasion check box, and then click Send.
Check 5: If the intensity is set high, reduce the Intensity setting in the printer driver and try printing again
If you are using plain paper to print images with high intensity, the paper may absorb too much ink and become wavy, causing paper abrasion.
Reduce the Intensity setting in the printer driver and try printing again.
1.Open the printer properties dialog box.
2.On the Main sheet, select Manual for Color/Intensity, and then click Set.
3.Drag the Intensity slide bar on the Color Adjustment sheet to adjust the intensity.
1.Open the Print dialog box.
2.Select Color Options in the pop-up menu.
3.Drag the Intensity slide bar to set the intensity.
If you are printing beyond the recommended printing area of your printing paper, the lower edge of the paper may become stained with ink.
Resize your original document in your application software.
->[ Printing Area ]
Clean the Paper Feed Roller.
->[ Routine Maintenance ]
NOTE
Cleaning the Paper Feed Roller will wear the roller, so perform this procedure only when necessary.
When performing duplex printing, the inside of the printer may become stained with ink, causing the printout to become smudged.
Perform the Bottom Plate Cleaning to clean the inside of the printer.
NOTE
To prevent the inside of the printer from stains, set the paper size correctly.
Doing so gives the printed surface enough time to dry so that paper smudged and scratched are prevented.
1.Make sure that the printer is turned on.
2.Open the printer properties dialog box.
3.Click the Maintenance tab and then Custom Settings.
4.Drag the Ink Drying Wait Time slide bar to set the wait time, and then click Send.
5.Confirm the message and click OK.
1.Make sure that the printer is turned on.
2.Open the Canon IJ Printer Utility.
3.Select Custom Settings in the pop-up menu.
4.Drag the Ink Drying Wait Time slide bar to set the wait time, and then click Send.
5.Confirm the message and click OK.
Depending on the media type, the paper may be scratched by other loaded paper when feeding from the Rear Tray. In this case, load one sheet at a time.
Check 1: Did you confirm the paper type and print quality settings?
Check 2: Is the size of the loaded paper correct?
The margin may be smudged if the size of the loaded paper is larger than that specified in the printer driver.
Set the paper size correctly according to the paper you loaded.
NOTE
This printer performs automatic cleaning when necessary to keep printouts clean. A small amount of ink is ejected for cleaning.
Although ink is usually ejected on the ink absorber, it may be ejected on the paper if you load paper larger than that specified with the printer driver.