How to perform the wireless LAN setup manually (Macintosh)

Last Updated : 23-Jul-2009
Issue Number : 8200572700

Solution

Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network.

Notes on Network Connection

The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.
In an office setup, consult your network administrator.
If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
The machine cannot be used over a wireless and wired connection at the same time.
If an error message appears or if you have trouble with the network connection, refer to the printed manual: Network Setup Troubleshooting.

NOTE

To use the machine on additional computers (after connecting it to the first computer), refer to [ How to perform the wireless LAN setup so that other computers can share the same printer (Macintosh) ]

[ Wireless Connection ]

Connect to your network environment over a wireless connection.

An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported.

Be sure to prepare an access point.

Wireless Setup

Check the Information for Wireless Connection

The following information is required to connect to your access point or router.

Check your access point or router for the following information, then write it down.

NOTE

For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.

- Access Point Name/Network Name:

* Also referred to as SSID.

An identifier to identify the specific access point.

- Network Key:

* Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.

A password required to set to prevent unauthorized access to communication.

1. Use the Easy-Scroll Wheel (A) to select Settings, then press the OK button.

2. Select Wireless LAN setup, then press the OK button.

3. Select Yes, then press the OK button.

When wireless connection is enabled, the Wi-Fi lamp (B) lights blue.

4. Select Easy settings, then press the OK button.

5. Select the access point name you wrote down, then press the OK button.

NOTE

If you are living in an apartment, nearby access points in use may be detected.

6. When one of the following screens is displayed, enter the network key you wrote down, then press the OK button.

If the following screen is not displayed, go to step 8.

Use the Easy-Scroll Wheel to select the character. Use the

button to move the cursor to the right.

IMPORTANT

Enter upper and lower case letters of the alphabet correctly.

7. Make sure that the network key is correct, then press the OK button.

8. When the completion screen appears, press the OK button, then press the HOME button (C).

The standby screen returns.

NOTE

If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual:Network Setup Troubleshooting.

Confirm Connection Status

1. Press the HOME button (A), select Settings using the Easy-Scroll Wheel (B), then press the OK button.

IMPORTANT

Confirm connection status after installing the machine in the target location.

2. Select Device settings, then press the OK button.

3. Select LAN settings, then press the OK button.

4. Select Confirm LAN settings, then press the OK button.

5. Select Wireless LAN setting list or Wired LAN setting list, then press the OK button.

Make sure that Connection is set to Active, then press the HOME button.

It may take a while before the connection is complete. In this case, press the Back button (C) and wait for about a minute, then display the Wireless LAN setting list screen or Wired LAN setting list screen again.

NOTE

If the communication status does not improve, make sure of the following.

- The machine and network device are turned on.

- There is no obstacle between the machine and access point, and wireless communication is possible.

- There is no microwave, refrigerator or any other object that may cause radio interference nearby.

Install the Software

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications to be installed.)

IMPORTANT

Quit all running applications before installation.
Log on as the administrator (or a member of the Administrators group).
Do not switch users during the installation process.
Internet connection may be required during the installation. Connection fees apply.
It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.
Mac OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported.

1. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

2. Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.

If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

NOTE

If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.

3. Select your place of residence, then click Next.

NOTE

If the Select Language screen appears, select a language, then click Next.

4. Select a country or region, then click Next.

NOTE

Displayed only when Europe, Middle East, Africa or Asia is selected on the screen in step 3.

5. Click Easy Install.

The drivers, application software, and on-screen manuals are installed all together.

NOTE

If you want to select particular items to install, click Custom Install.

6. Click Install.

7. Select Use the printer on network, then click Next.

8. Read the License Agreement screen carefully and click Yes.

IMPORTANT

Follow any on-screen instructions to proceed with the software installation.

9. When the Printer Detection screen appears, click Next.

IMPORTANT

If the Printer Detection screen is not displayed, the connection method is not correctly selected in step 7. Follow on-screen instructions and proceed with the installation. Click Exit on the installation complete screen, then start again from step 2 and be sure to select Use the printer on network in step 7.

10. On the Canon IJ Network Tool screen, select MP990 series in Printers, then click Next.

NOTE

If the machine is not detected, refer to the printed manual: Network Setup Troubleshooting. Make sure there is no problem, then click Update.

11. When the Connection Performance Measurement screen appears, click Next.

Confirm the measurement results, then click Finish.

Ensure that

is displayed in Connection performance between the printer and the access point.

NOTE

You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setup. For details, refer to the on-screen manual: Advanced Guide.
If an icon other than appears, improve the communication status by referring to the displayed message or the help file, then click Remeasurement.

Install the Software (Registration)

This section describes how to register the machine on a Macintosh computer.

1. When the Register Printer and Scanner screen appears, click Register Printer.

Proceed to the section that relates to your operating system for further installation instructions.

Mac OS X v.10.5.x Go to Step 2-A

Mac OS X v.10.4.x Go to Step 2-B

Mac OS X v.10.3.9 Go to Step 2-C

NOTE

The alphanumeric characters after Canon MP990 series is the machine's Bonjour service name or MAC address.
If the machine has not been detected, make sure of the following.

－ The machine is turned on.

－ The firewall function of any security software is turned off.

－ Wireless Connection: The computer is connected to the access point.

2-A (Mac OS X v.10.5.x)

(1) Select Canon MP990 series and click Add.